badcc8fba2
Development.md describes the wire-layer convention (one directory per Onvif Web Service, gen_commands.py for new SOAP command types) but does not mention that some directories also ship hand-written higher-level helpers built on top of those types. A new contributor reading the doc could reasonably assume event/ is purely auto-generated and miss event/stream. Adds a 'Higher-level helpers' section that calls out: * event/stream — the new channel-based event consumer. * event/topic — the existing topic identifier helpers. Also documents the placement convention (sub-package under the relevant web service directory) so future helpers land in a predictable spot.
Onvif library
Simple management of onvif IP-devices cameras. onvif is an implementation of ONVIF protocol for managing onvif IP devices. The purpose of this library is convenient and easy management of IP cameras and other devices that support ONVIF standard.
Overview
This repository is forked from: use-go/onvif
Supported services
The following services are implemented:
- Device
- Media
- PTZ
- Event
- Discovery
Using
General concept
- Connecting to the device
- Authentication (if necessary)
- Defining Data Types
- Carrying out the required method
Connecting to the device
If there is a device on the network at the address 192.168.13.42, and its ONVIF services use the 1234 port, then you can connect to the device in the following way:
dev, err := onvif.NewDevice(onvif.DeviceParams{Xaddr: "192.168.13.42:1234"})
The ONVIF port may differ depending on the device , to find out which port to use, you can go to the web interface of the device. Usually this is 80 port.
Authentication
If any function of the ONVIF services requires authentication, you must use the Authenticate method.
device := onvif.NewDevice(onvif.DeviceParams{Xaddr: "192.168.13.42:1234", Username: "username", Password: password})
Defining Data Types
Each ONVIF service in this library has its own package, in which all data types of this service are defined, and the package name is identical to the service name and begins with a capital letter. onvif defines the structures for each function of each ONVIF service supported by this library. Define the data type of the GetCapabilities function of the Device service. This is done as follows:
capabilities := device.GetCapabilities{Category:"All"}
Why does the GetCapabilities structure have the Category field and why is the value of this field All?
The figure below shows the documentation for the GetCapabilities. It can be seen that the function takes one Category parameter and its value should be one of the following: 'All', 'Analytics',' Device ',' Events', 'Imaging', 'Media' or 'PTZ'`.
An example of defining the data type of GetServiceCapabilities function in PTZ:
ptzCapabilities := ptz.GetServiceCapabilities{}
The figure below shows that GetServiceCapabilities does not accept any arguments.
Common data types are in the xsd/onvif package. The types of data (structures) that can be shared by all services are defined in the onvif package.
An example of how to define the data type of the CreateUsers function in Devicemgmt:
createUsers := device.CreateUsers{User: onvif.User{Username:"admin", Password:"qwerty", UserLevel:"User"}}
The figure below shows that ,in this example, the CreateUsers structure field must be a User whose data type is the User structure containing the Username, Password, UserLevel, and optional Extension fields. The User structure is in the onvif package.
Carrying out the required method
To perform any function of one of the ONVIF services whose structure has been defined, you must use the CallMethod of the device object.
createUsers := device.CreateUsers{User: onvif.User{Username:"admin", Password:"qwerty", UserLevel:"User"}}
device := onvif.NewDevice(onvif.DeviceParams{Xaddr: "192.168.13.42:1234", Username: "username", Password: password})
device.Authenticate("username", "password")
resp, err := dev.CallMethod(createUsers)
Development
See here